Sterling 5405-59DR-G05 Installation Guide

Browse online or download Installation Guide for Unknown Sterling 5405-59DR-G05. STERLING 5405-59DR-G05 Installation Guide User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 6
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Groove
1
2
3
x2
x2
Leg
x2
#8-18 x 1-1/2"
Screw
Cover
Screw Cover
Notch
Tin Snips
Miter Box
32 Teeth Per Inch Blade
Masking Tape
100% Silicone Sealant
1/16"
3/16", 5/16" 5/16" Masonry Bit for Tile
Series Number Label
1077762
Anchor
1081001
Bumper
1031943**
Screw Cover
1205305** Hanger Bracket Kit 1203634 Hardware Skin Pack
1058827-02**
Top Track
1051142-A
Screw #8-32 x 3/8"
1199426-01**
Hanger Bracket
1050048-B
Barrel Nut
1077763-A
Bolt #8-32 x 1/4"
Wall Jamb*
1093027
Spacer (8 ea.)
1044585
Roller
Door Panel*
1057704-02**
[20" (508 mm)]
1057704-01**
[24" (610 mm)]
Towel Bar
1056868-A
Screw
1048208-C
Screw #8-18 x 1-1/2"
1058294**
Center Guide
1058626-02**
Bottom Track
1053530
Insert
1199110
Gasket
Bottom Wall Jamb Notch
"A" Mark
Cut Line
1/4" (6 mm)
A
Insert
Bottom Track
Correct Incorrect
Slide the notched end of the insert into the
groove and pull the notch to the end of the
bottom track. Trim the insert to be flush with the
bottom track.
Measure distance “A.” Subtract 1/4” (6 mm) or
the width of a number 2 pencil from “A” and cut
the bottom track.
Position the bottom track on the center of the
ledge. If needed, file the ends to match the
corners.
Center the bottom track on the ledge with the leg
to the outside. Tape the bottom track in place and
mark the position.
IMPORTANT! The bottom track and wall jamb
must sit flat against the shower ledge and the
wall. If needed, trim and file the wall jamb. Use a
coin to match and to transfer the corner radius of
the shower to the wall jamb.
Position the wall jambs over the bottom track.
Plumb both wall jambs. Mark the screw holes.
Remove the wall jambs. Drill 5/16” holes into the
walls and insert the anchors.
Apply silicone sealant in the groove on the
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
Reposition both wall jambs. Secure the wall
jambs with screws. Attach a bumper at the top
and bottom locations.
Check the bumpers for the correct horizontal
alignment with the wall jambs.
5400 Series Sliding Shower and Bath Doors
Sliding Bath Doors Sliding Shower Doors
11204884-2-E
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310
1204884-2-E
Installation and Care Instructions
Required Tools Parts Identifi cation
2 3 4
7 86 9
1 5
10
SterlingPlumbing.com
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
IMPORTANT! Do not touch the edges of the tempered glass with tools or
any other hard objects. Do not set the unframed tempered glass directly on
the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the bottom track.
NOTICE: The warranty does not apply to a product that has been modified
or altered in a manner other than as expressly permitted in the Installation
and Care Guide.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for application and
curing time.
To watch this installation online, visit the product page at
www.sterlingplumbing.com.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Critical Information!
Read Before Installation!
Read and follow all instructions.
*Need help? Contact the STERLING Customer Care Center
at 1-800-STERLING (1-800-783-7546).
For service parts information, care and cleaning, and
other information, visit www.sterlingplumbing.com
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Page view 0
1 2 3 4 5 6

Summary of Contents

Page 1 - Read Before Installation!

Groove123x2x2Legx2#8-18 x 1-1/2"Screw CoverScrew CoverNotchTin SnipsMiter Box32 Teeth Per Inch BladeMasking Tape100% Silicone Sealant1/16"3/

Page 2 - Warranty

ReversibleGasketx2Hanger Bracketx28-32 x 1/4"Barrel NutHanger BracketNo Gap at TopBoltx2LabelScrewRollerLabel Side#8-32 x 3/8"x2Label Side#8

Page 3 - Lire et suivre toutes les

Rainure123x2x2Piedx2#8-18 x 1-1/2"Cache-vis Cache-visEncocheCisailles de ferblantierBoîte à ongletsLame de 32 dents par pouceRuban-cacheMastic 10

Page 4 - Garantie

RéversibleJoint d'étanchéitéx2Étrier de suspensionx28-32 x 1/4"Écrou à portée cylindrique Étrier de suspensionPas d'espacement en haut

Page 5 - ¡Información crítica!

Ranura123x2x2Patax2#8-18 x 1-1/2"Cubre tornillo Cubre tornilloMuescaTijeras para chapaCaja de ingletesHoja de 32 dientes por pulgadaCinta de enma

Page 6 - Garantía

ReversibleEmpaquex2Soporte de suspensiónx28-32 x 1/4"Tuerca cilíndrica Soporte de suspensiónSin separación en la parte superior Pernox2EtiquetaTo

Comments to this Manuals

No comments