Front
Edge
Level
Wall Jamb
Pencil
x2
Front
Edge
Wall Jamb
Expander Jamb
x2
Front
Edge
Screws
#8-18 x
1-3/4"
x2
Front Edge
Silicone Sealant
5/16" Drill
Bit
x2
3
1
2
Expander
Jamb
Adjustment Block
Wall Jamb
1/2"
(13 mm)
Tape
Screw
x4
Screw
#8 x 3-1/2"
Tin Snips
Masking Tape100% Silicone Sealant
Assorted Drill Bits
Hardware Pack
1080993**
1088417
Bushing
1088416
Pivot Pin
(Deep Bronze)
682040
(Matte Silver)
682039
Column
(Nickel)
(Brass)
(Silver)
682001
682011
682038
(Matte Silver)
(Nickel)
(Deep Bronze)
681546
(Silver)
681501
(Brass)
681511
681544
681545
Wall Jamb
1031813
Adjustment Block
Series
Number Label
(Matte Silver)
(Nickel)
(Deep Bronze)
919934
(Silver)
919918
(Brass)
919919
919932
919933
Bridge Member (Includes Seal 521307)
(Black)1049018-T
(Silver)
(Brass)
1049018-D
1049018-L
Screw
Door Panel*
(Includes Magnet 681301)
Side Panel*
Side Panel*
1031659-C
Screw
1031659-C
Screw
1077762
Anchor
1048208-A
Screw
1088418
Plug
1088771
Panel Cushion
681301
Magnet
681200
Magnet
521311
Seal
521307
Seal
521307
Seal
1052892-A
Washer
1088417
Bushing
1088416
Pivot Pin
(Matte Silver)
684131
Strike Post (Includes Magnet 681200)
(Nickel)
(Brass)
(Deep Bronze)
684132
(Silver)
684101
684110
684130
(Matte Silver)
684031
Flange (Includes Seal 521311)
(Nickel)
(Brass)
(Deep Bronze)
684032
(Deep Bronze)
682040
(Silver)
684001
684010
684030
(Matte Silver)
682039
Column
(Nickel)
(Brass)
(Silver)
682001
682011
682038
(Matte Silver)
(Nickel)
(Deep Bronze)
681546
(Silver)
681501
(Brass)
681511
681544
681545
Wall Jamb
(Black)1049018-S
(Silver)
(Brass)
1049018-J
1049018-K
Screw
Front
Edge
Front
Edge
3/4"
(19 mm)
3/4"
(19 mm)
Mark the location of the wall jambs. The front
edge should be 3/4” (19 mm) from the front edge
of the threshold.
Move the wall jambs into place and check the fit.
When needed, snip and file the bottom edges of
the wall jambs for a snug fit.
Align the front edge of the wall jambs with the
marks. Plumb the wall jambs. Mark the front
edges of the wall jambs and the wall jamb holes.
Remove the wall jambs. Drill 5/16” holes at each
mark and insert an anchor in each hole.
Slide an adjustment block onto each end of the
wall jambs, positioned over the first hole. Secure
in place with tape. Loosen the adjustment in each
adjustment block until it extends 1/2” (13 mm).
Apply a bead of silicone sealant to the groove
along the entire wall jamb.
Move a wall jamb into place with the sealant
groove against the wall, toward the outside of
the shower. Secure with three screws. Repeat for
other side.
Carefully lift the side panels onto the shower
ledge. Align the expander jamb on the panel with
the wall jamb.
Use a screwdriver to tighten or loosen the
adjustment blocks until they firmly and evenly
contact the wall frame.
Secure the wall panels in place with two screws.
SP2270 Series Neo-Angle Shower Doors
IMPORTANT! Do not cut the top track the same length as the bottom track.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for application and
curing time.
To watch this installation online; visit the product page at
www.sterlingplumbing.com.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
11187937-2-C
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310
1187937-2-C
Installation and Care Instructions
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Required Tools Parts Identifi cation
2 3 4
7 86 9
1 5
10
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
NOTICE: Do not touch the edges of the tempered glass with tools or any
other hard objects. Do not set the unframed tempered glass directly on the
floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
SterlingPlumbing.com
(44 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals